A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The content down below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is pretty much captivating. Read on and draw your own personal final thoughts.
Setting up a tub isn't precisely rocket science, however it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently accessible, the job can relocate quickly; if you have to open up a wall to remove the old bathtub and position the brand-new tub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the brand-new one. See to it you have actually qualified yourself for the work and are comfortable trying it. Instead of working with a service provider to take over a halfway-completed project, it is far better to think about utilizing one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your restroom if you have actually currently gotten a brand-new tub and also do not need to alter the plan of your previous water supply pipelines.
Your devices and also product list ought to make up the following:
Preparing for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly bothersome as a result of the restricted accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, place the bathtub in the required position. The wooden boards are practical in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub till the level checks out degree.
To install taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the water supply as well as check all joints and brand-new pipework for leaks and tighten them if needed. Fill the bath tub as well as likewise examine the overflow outlet as well as the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and sealing around the tub must wait up until the bathtub has been used a minimum of once as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area in between the faucet and also the sink. Protect the faucet in place with the maker supplied backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind should be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, triggering the water to permeate the wall surface between the bath and the tiling, causing issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and also cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can break rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I discovered that review about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the internet. Don't hesitate to take a moment to share this blog if you appreciated it. I enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Additional Resources Report this page